德國BURKERT寶德類型 2836 - 直動式二通比例電磁閥工作原理： 想必很多廠家對寶德產品都不陌生，但是了解他的原理應該不多，下面是我司對產品的做了一些詳情，
直動式比例閥 2836 型是電磁力驅動的控制閥，適用于相對流量較高的應用。閥門是常閉型。
適用于高流量
直動式，常閉
工作壓力0 ...25 bar
DN 3.0...12 mm
連接接口 1/2”和 3/4” 
The direct-acting solenoid control valve,
Type 2836, works as an electromagnetically
actuated control valve in applications with
relatively high flow rates. The valve is normally
closed.
Valve operation A
Valve control takes place through the control
electronics of Type 8605, which converts an
analogue input signal into a PWM2) (pulsewidth
modulation) signal.
Further, functional features of the Type 8605
electronic control unit:
• Temperature compensation for coil heating
by internal current regulation
• Simple zero and span settings
• Ramp function to dampen fast status
changes
Type 2508
Cable plug
Type 2836 can be combined with...
• Direct-acting, normally closed
• DN3 to 12 mm
• Port Connection ½" or ¾"
2/2 way direct-acting,
solenoid proportional
control valve
Technical data - valve
Body material Brass, stainless steel
Seal material FKM, others on request
Fluids Neutral gases and liquids
Pressure range 0 to 25 bar1)
Fluid temperature -10 to +90 °C (14 °F to 194 °F)
Ambient temperature max. +55 °C (max. 131 °F)
Viscosity max. 21 mm2/s (max. 21 cSt)
Power supply 24 V DC
PWM frequency 150-180 Hz
Power consumption max. 24 W
Max. coil current 1100 mA
Duty cycle 100% continuously rated
Port connection G ½, G ¾, NPT ½, NPT ¾, others on request
Electrical connection Cable plug Type 2508 acc. to DIN EN 175301-803 form A
Installation As required, preferably with actuator in upright position
Typical control data3)
Hysteresis
Repeatability
Sensitivity
Span
<5%
<1% of F.S.
<0.5% of F.S.
1:25
Protection class - valve IP65
1) Pressure data [bar]: Overpressure with respect to
atmospheric pressure
2) PWM pulse-width modulation
3) Characteristic data of control behaviour depends on
process conditions
比例電磁閥工作原理
它基于電磁開關閥的原理：斷電時，彈簧將鐵心直接壓在閥座上，使閥門關閉。線圈通電時，所產生電磁力克服彈簧力將鐵心提起，從而打開閥門。比例電磁閥對電磁開關閥的結構作了一些改動：在任何線圈電流下，使彈簧力與電磁力之間產生平衡。線圈電流的大小或電磁力的大小將影響柱塞的行程和閥門開度，而閥門開度(流量)與線圈電流(控制信號)之間為理想的線性關系。 直動式比例電磁閥的流向?yàn)殚y座下。介質從閥座下方流入，其作用力的方向與電磁力相同，而與彈簧力相反。因此，需要設置工作狀態下對應于工作范圍(線圈電流)的大和小流量值。得雷流體的比例電磁閥在斷電時都是關閉的(NC，常閉型)。
轉載請注明文章出處：http://www.queenus.com.cn |
